nix-store manipulate or query the Nix store nix-store --verbose -v --keep-failed -K operation options arguments The command nix-store performs primitive operations on the Nix store. You generally do not need to run this command manually. nix-store takes exactly one operation flag which indicates the subcommand to be performed. These are documented below. This section lists the options that are common to all operations. These options are allowed for every subcommand, though they may not always have an effect. &opt-verbose; --keep-failed / -K Specifies that in case of a build failure, the temporary directory (usually in /tmp) in which the build takes place should not be deleted. The path of the build directory is printed as an informational message. The following environment variables affect the behaviour of nix-store. TMPDIR=path Use the directory path to store temporary files. In particular, this includes temporary build directories; these can take up substantial amounts of disk space. The default is /tmp. nix-store --realise -r paths The operation --install realises in the file system the store expressions stored in paths. If these expressions are derivation expressions, they are first normalised into a closure expression. This may happen in two ways. First, the corresponding closure expression (the successor) may already known (either because the build has already been performed, or because a successor was explicitly registered through the --successor operation). Otherwise, the build action described by the derivation is performed, and a closure expression is computed by scanning the result of the build for references to other paths in the store. The paths of the closure expression corresponding to each expression in paths is printed on standard output. nix-store --delete -d paths The operation --delete unconditionally deletes the paths paths from the Nix store. It is an error to attempt to delete paths outside of the store. This operation should almost never be called directly, since no attempt is made to verify that no references exist to the paths to be deleted. Therefore, careless deletion can result in an inconsistent system. Deletion of paths in the store is done by the garbage collector (which uses --delete to delete unreferenced paths). nix-store --query -q --list -l --requisites -R --predecessors --graph --normalise -n --force-realise -f args The operation --query displays various bits of information about store expressions or store paths. The queries are described below. At most one query can be specified. The default query is --list. --normalise / -n For those queries that take a Nix store expression, this option causes those expressions to be normalised first. --force-realise / -f For those queries that take a Nix store expression, this option causes those expressions to be realised first. This is just a short-cut for the common idiom nix-store --realise /nix/store/bla.store x=`nix-store --query --normalise /nix/store/bla.store (do something with the path $x which using this flag can be written as x=`nix-store --query --normalise --force-realise /nix/store/bla.store (do something with the path $x --list / -l Prints out the output paths of the store expressions indicated by the identifiers args. In the case of a derivation expression, these are the paths that will be produced when the derivation is realised. In the case of a closure expression, these are the paths that were produced the derivation expression of which the closure expression is a successor. --requisites / -R Prints out the requisite paths of the store expressions indicated by the identifiers args. The requisite paths of a Nix expression are the paths that need to be present in the system to be able to realise the expression. That is, they form the closure of the expression in the file system (i.e., no path in the set of requisite paths points to anything outside the set of requisite paths). The notion of requisite paths is very useful when one wants to distribute store expressions. Since they form a closure, they are the only paths one needs to distribute to another system to be able to realise the expression on the other system. This query is generally used to implement various kinds of deployment. A source deployment is obtained by distributing the requisite paths of a derivation expression. A binary deployment is obtained by distributing the requisite paths of a closure expression. A cache deployment is obtained by distributing the requisite paths of a derivation expression and specifying the option --include-successors. This will include not just the paths of a source and binary deployment, but also all expressions and paths of subterms of the source. This is useful if one wants to realise on the target system a Nix expression that is similar but not quite the same as the one being distributed, since any common subterms will be reused. This query has a number of options: --exclude-exprs Excludes the paths of store expressions. This causes the closure property to be lost, that is, the resulting set of paths is not enough to ensure realisibility. --include-successors Also include the requisites of successors (normal forms). Only the requisites of known successors are included, i.e., the normal forms of derivation expressions that have never been normalised will not be included. Note that not just the successor of a derivation expression will be included, but also the successors of all input expressions of that derivation expression. I.e., all normal forms of subterms involved in the normalisation of the top-level term are included. --predecessors For each store expression stored at paths args, prints its predecessors. A derivation expression p is a predecessor of a store expression q iff q is a successor of p. --graph Prints a graph of the closure of the store expressions identified by args in the format of the dot tool of AT&T's GraphViz package. nix-store --successor srcpath sucpath The operation --successor registers that the closure expression in sucpath is a successor of the derivation expression in srcpath. This is used to implement binary deployment. nix-store --substitute srcpath subpath The operation --substitute registers that the store path srcpath can be built by realising the derivation expression in subpath. This is used to implement binary deployment. nix-store --verify The operation --verify verifies the internal consistency of the Nix database, and the consistency between the Nix database and the Nix store. Any inconsistencies encountered are automatically repaired. Inconsistencies are generally the result of the Nix store or database being modified by non-Nix tools, or of bugs in Nix itself.